Compare Models

Home › Showroom › Compare Models

2024 Exmark Lazer Z E-Series 60 in. Briggs Vanguard 26 hp in Conway, Arkansas — 2024 Exmark Lazer Z E-Series 60 in. Briggs Vanguard 26 hp

View Details

Specs
Features

General Information

Manufacturer

Exmark

Model Year

2024

Model

Lazer Z E-Series 60 in. Briggs Vanguard 26 hp

Model Code

LZE810GBV604A3

Color

Red

Body

Frame

Caster Forks - 0.50 in. thick caster yoke arms

Tractor Frame - Unibody, welded, heavy-duty 1.5 x 3 in. tubular steel

Caster Forks - 0.50 in. thick caster yoke arms

Tractor Frame - Unibody, welded, heavy-duty 1.5 x 3 in. tubular steel

Seat

Deluxe, bolstered suspension seat with Elastomeric Vibration Control material

Seat Adjustment

Fore and aft from Operators’ Position

Rollover Protection (ROPS)

2-post foldable ROPS standard with seat belt and latch

Drivetrain

Transmission/Drive

Hydro drive

Wheels/Tires

Wide pneumatic

Drive Tires

24 x 12-12, 4 ply Super Turf®

Steering Tires

Front Caster Tires - 13 x 6.50-6, smooth-tread, semi-pneumatic

Parking Brake

Lever-actuated disc

Electrical

Battery

12V with 15A alternator

Instrumentation

Digital

Hour Meter

Engine

Engine Make

Briggs

Engine Model

Vanguard 810

Horsepower

26 hp

Starter

Electric

Fuel Type

Gas carbureted

Fuel Capacity

8 gal. with single fill location

Measurements

Length

83.1 in. (211.1 cm)

Width

72.8 in. (184.9 cm)

Height

70.5 in. (179.1 cm)

Weight

Curb - 1,279 lb.

Mowing Width

60 in.

Mowing Height Range

1.0 - 5.5 in. (2.5 - 11.8 cm) in 0.25 in. (0.64 cm) increments

Operational

Steering

Control - Hydraulically dampened twin levers, adjust fore and aft. Adjustable dampeners (3 positions) to customize drive responsiveness. Also adjustable to 2 height positions

Deck Construction

10 ga. top that is formed and continuously seam welded, 7 ga. side skirt and 7 ga. formed and welded spindle mounting locations for improved strength and reduced weight

Deck Style - Floating Deck

Deck Style Description - Full-floating UltraCut Series 4. Side discharge standard

10 ga. top that is formed and continuously seam welded, 7 ga. side skirt and 7 ga. formed and welded spindle mounting locations for improved strength and reduced weight

Deck Style - Floating Deck

Deck Style Description - Full-floating UltraCut Series 4. Side discharge standard

Spindles

BladeNo maintenance, sealed and non-greasable spindles, 7.75 in. diameter cutter housing with 0.98 in. (25 mm) diameter spindle shaft and splined blade driver.

Blades

3 at 20.50 in. length

Blade Tip Speed

Approximately 18,500 fpm

Other

Includes

Cup holder

Features

HYDRO DRIVE, SIMPLIFIED: Our hydro drive system has no hoses to leak and just one easy-to-change belt. Only simple, annual maintenance is required. It also lowers the center of gravity for improved handling.
UNIBODY FRAME: Our one-piece body frame is a classic case of “less is more.” Because, fewer parts equal more strength. And, more durability. So, in the interest of accuracy, the Lazer Z’s unibody frame is actually a case of “less is way more.”
LESS TIME AT THE PUMP: Gas-powered E-Series models have a single 8-gallon tank with one fill location.
ON-BOARD DIAGNOSTICS: Check vital functions at a glance on the digital screen. An electronic fuel gauge with low fuel warning on all Lazer Z units, battery voltage warning, hour meter and OPC safety switch monitoring make troubleshooting easy.
FEWER GREASE POINTS: With just four grease points that only need annual greasing, the Lazer Z delivers maximum performance with minimum maintenance. Greaseless spindles and only four grease points on the entire machine.
ULTRACUT SERIES 4 DECK: This full-floating deck uses maintenance free spindle with a splined blade driver to stop bolt tightening on impacts. And, our patented bearing design on idler arm pivots only needs annual service.
REAR DISCHARGE DECK: Available in 60 and 72 inch cutting widths, the rear discharge deck offers increased clipping discharge control, reduced noise, and the ability to trim on both sides of the cutting deck while keeping the operator clean.
TOOL-LESS BELT REMOVAL: Deck and hydro belt can be installed without using any tools.

Features

HYDRO DRIVE, SIMPLIFIED: Our hydro drive system has no hoses to leak and just one easy-to-change belt. Only simple, annual maintenance is required. It also lowers the center of gravity for improved handling.
UNIBODY FRAME: Our one-piece body frame is a classic case of “less is more.” Because, fewer parts equal more strength. And, more durability. So, in the interest of accuracy, the Lazer Z’s unibody frame is actually a case of “less is way more.”
LESS TIME AT THE PUMP: Gas-powered E-Series models have a single 8-gallon tank with one fill location.
ON-BOARD DIAGNOSTICS: Check vital functions at a glance on the digital screen. An electronic fuel gauge with low fuel warning on all Lazer Z units, battery voltage warning, hour meter and OPC safety switch monitoring make troubleshooting easy.
FEWER GREASE POINTS: With just four grease points that only need annual greasing, the Lazer Z delivers maximum performance with minimum maintenance. Greaseless spindles and only four grease points on the entire machine.
ULTRACUT SERIES 4 DECK: This full-floating deck uses maintenance free spindle with a splined blade driver to stop bolt tightening on impacts. And, our patented bearing design on idler arm pivots only needs annual service.
REAR DISCHARGE DECK: Available in 60 and 72 inch cutting widths, the rear discharge deck offers increased clipping discharge control, reduced noise, and the ability to trim on both sides of the cutting deck while keeping the operator clean.
TOOL-LESS BELT REMOVAL: Deck and hydro belt can be installed without using any tools.

Compare Models

2024 Exmark Lazer Z E-Series 60 in. Briggs Vanguard 26 hp

2024 Exmark Lazer Z E-Series 60 in. Briggs Vanguard 26 hp

General Information

Body

Drivetrain

Electrical

Engine

Measurements

Operational

Other

Features

Features